Updated November 2026

Paws and Pals automatic pet feeder instructions come down to four jobs: power the unit, set the clock, program your meal times and portions, and run a test dispense before you trust it with a full day of feeding. Work through them in that order and you should have a feeder dispensing on schedule within about 20 minutes. Exact button labels and menus vary by model, so check the manual that came in your box against the steps below.

Before You Start: Unpack and Prepare

Most problems people report with these feeders trace back to skipped preparation, not the programming itself. Set aside a few minutes before you touch the unit.

Shopping for one? See our guide: Paws and Pals Automatic Pet Feeder: 6 Best Picks Compared (2026).

  • Remove the food hopper, lid, and food tray, and wash them in warm soapy water. Dry them completely.
  • Confirm you have the power adapter and, if your model uses them, batteries for backup.
  • Place the feeder on a flat, stable surface near an outlet, out of direct sun and away from water bowls.
  • Check that the dispensing bowl or tray sits level and locks into place.

Setting Up Power and the Clock

Plug the adapter into the feeder first, then into a wall outlet. If your model has a battery compartment, install the batteries now so the clock survives a power interruption. Set the current time and day before anything else, because every scheduled meal depends on an accurate clock. A feeder with the wrong time will dispense at odd hours, which is one of the most common complaints owners raise.

Programming Meal Times and Portions

Program meals one at a time. Most Paws and Pals units let you choose a time, then a portion size, usually counted in cups or in dispense cycles depending on the model. Start with a schedule your pet already follows, such as 7:00 a.m. and 6:00 p.m., and set a portion that matches your vet’s guidance for your pet’s weight and food. Save the schedule and confirm the screen shows each meal as active.

If your feeder supports a manual dispense button, use it to run one test portion. Watch the food drop and confirm the amount looks right in the bowl. Adjust the portion size if needed before you rely on the schedule.

Testing and Checking It Works

Run the feeder for at least one full day before leaving town. Check the bowl after each scheduled meal, and confirm your pet is eating. Pay attention to any clicking or grinding, and confirm the hopper is not jammed with kibble. Food that is too large, wet, or oily can clog the auger or chute, so stick to dry kibble sized for the feeder.

Common Mistakes

  • Leaving the clock on the wrong time or AM/PM setting, which shifts every meal.
  • Filling the hopper with wet food or treats that stick together and jam the mechanism.
  • Skipping the test dispense and assuming the portion size is correct.
  • Forgetting that the lid must be fully closed for the feeder to start.
  • Placing the unit on a soft or uneven surface, which can throw off the dispensing tray.

A few supplies make daily use easier and reduce setup headaches.

  • PetSafe Smart Feed 2.0: a well-known programmable feeder that many owners use as a reference point for how these units are typically set up. View on Amazon
  • Petlibro Granary Automatic Feeder: a common alternative with a large hopper, useful if you want fewer refills. View on Amazon

FAQ

What if my Paws and Pals feeder won’t dispense?

First confirm the power adapter is plugged in and the clock is set correctly. Then check the hopper and chute for jammed kibble. Consult the manufacturer’s manual or support line for model-specific troubleshooting.

How do I know the right portion size?

Start with the feeding guidance from your veterinarian or the food bag, then adjust based on your pet’s body condition. Consult a veterinarian if your pet is gaining or losing weight unexpectedly.

Can I reset the feeder if I get the schedule wrong?

Most models let you clear or edit individual meal entries from the menu. Check your manual for the exact reset steps, since the procedure differs between versions.

Conclusion

Set the power, clock, and meal schedule, then run a test dispense before relying on the feeder. Most setup problems come from a wrong time or a jammed hopper, so check both first. Keep the manual handy for model-specific menus and fixes.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our everyday pet gear guides, checking product details against manufacturer specifications and owner feedback.