Updated November 2026
The westlink 6l automatic pet feeder food dispenser manual is the fastest route to a working feeder: it tells you how to unpack the unit, power it, load food, and program meal times. This guide walks you through finding the right manual, using its key sections, and running a first test feeding so you know the schedule will hold before you leave the house.
Find the Right Manual Before You Start
Manufacturers sometimes ship feeders with a printed quick-start card instead of a full booklet, so the complete document may live on the brand’s support page. Check the model number printed on the label on the underside or back of the hopper, and match it against the version you are holding. A 6-liter capacity model and a similarly named unit can have different button layouts, so a mismatched manual will send you looking for controls that aren’t there.
Shopping for one? See our guide: Arf Pets Automatic Pet Feeder Food Dispenser Review: Is It Worth It?.
Save a PDF copy to your phone as well as the paper copy. You will want to look up troubleshooting codes from the kitchen counter, not the floor behind the feeder.
Set Up the Feeder Step by Step
Most units in this category follow the same basic sequence. Read your manual’s version of each step, because button names and menu order vary.
- Place the feeder on a flat, dry surface near an outlet. Keep it away from water bowls and direct sun.
- Insert batteries if the manual calls for a backup supply, and confirm the clock shows the correct time before anything else.
- Plug in the adapter, then confirm the display lights up and the feeder reaches its idle state.
- Fill the food hopper and run one manual feed to check that kibble drops cleanly into the bowl.
- Program your meal times, portion size per feeding, and any daily total the menu allows.
- Watch the first scheduled feeding in person, or check the bowl within a few minutes after it runs.
Set Accurate Portions
Portion settings in most manuals are measured in cups or grams per serving, and the number on screen rarely matches what your pet eats. Pour a measured amount of your food into the bowl once, note how much the feeder dispenses, and adjust. Weigh a test dispense on a kitchen scale if you need tighter accuracy, and remember that kibble size changes the output. Your veterinarian can confirm a daily amount for your animal.
Program Timing and Power Backup
Schedule meals in a way that matches your routine, not just the clock on the wall. If you leave the house at 7:30 a.m., set the first feeding at least 15 minutes before you go so you can confirm it worked. Check whether your model stores the schedule during a power cut, and whether it resumes dispensing from the backup batteries. The manual normally states how long batteries hold a schedule, so write that number down.
Common Mistakes
- Skipping the test feed. A clogged hopper or wrong portion setting is far easier to catch on day one.
- Setting the clock to the wrong time zone or forgetting the daylight-saving change, which shifts every meal.
- Loading wet or oily food, which can jam the auger.
- Assuming the default portion is correct for your pet.
- Leaving the feeder unplugged after a move, which erases the schedule on some units.
Recommended Gear
A simple food scale helps you verify portions against your manual’s settings, which is more reliable than trusting the dial alone. View on Amazon
A sealed storage bin keeps kibble fresh and prevents clumping in the hopper between refills. View on Amazon
FAQ
Where can I find the westlink 6l automatic pet feeder food dispenser manual?
Check the box for a printed copy, then look up the model number on the brand’s support or download page. Match the document to the exact model printed on your feeder before following it.
What should I do if the feeder skips a scheduled meal?
Confirm the clock time and the schedule are correct, then check that the hopper has food and nothing is jamming the auger. Run a manual feed to test the mechanism, and look up any error code in the troubleshooting section.
Can I use any dry kibble in this feeder?
Most dispensers handle standard dry kibble, but very large, very small or sticky pieces can jam the mechanism. Confirm acceptable food types in your manual and test a small batch first.
Conclusion
Keep the manual handy, complete one full test cycle, and verify portions with a measured dispense before relying on the schedule. If your pet has a medical condition or special diet, confirm feeding amounts with your veterinarian. A few minutes of setup now prevents missed meals later.

